If the Ecn or Ec Message is Alternating with the Water Temperature on the Display, the Spa is Operating in the Economy Heating Mode. … The Water Temperature will probably drop Below Set Temperature between Filter Cycles. Other Heating Modes are Standard, Standard in Economy, and Sleep Modes.
What does EC mean on a strong spa?
Economy mode heats the spa to the set temperature only during filter cycles. “Ec” or “Ecn” will appear solid when the temperature is not current and will alternate with the temperature.
What does SL mean on Beachcomber hot tub?
This message……means…2) Std/St STANDARDThe hot tub is running in Standard Mode.3) Ecn/EC ECONOMYThe hot tub is running in Economy Mode.4) SLP/SL SLEEPThe hot tub is operating in sleep heating mode. If the display shows this message only, blinking, the hot tub is shut down.
How do I get my Balboa spa out of EC mode?
Low Range can be set between 10°C to 36°C. To change the range press the temp/warm button followed by the light button, then press temp/warm button again. To exit, press the light button or wait for 10 seconds to go back to the Main Screen.What does EC mean on a Viking Spa?
Economy Mode heats the spa to the set temperature only during. filter cycles. “Ec” will display solid when temperature is not current, and will alternate with temperature when temperature is current. Sleep Mode heats the spa to within 20°F/10°C of the set temperature only during filter cycles.
What mode should hot tub be on?
We reccommend setting your spa to “Auto” so that the water is always warm and ready for you to use. If you ever notice that your hot tub water temperature has dropped, but there are no error messages displayed on your control panel, you should check that the spa is set to “Auto” mode.
How do I turn up the heat on my Beachcomber hot tub?
To change heating modes, press the button then the button. To activate this jet pump, press the button once to activate low speed, twice to activate high speed and three times to turn the pump off. The low speed will turn off automatically after 4 hours and the high speed will turn off after 15 minutes.
What are the codes on a hot tub?
CODEERROR CODE DESCRIPTIONCE 04Water sensor/pressure switch faultCE 05Temperature sensor, or water is dangerously hotCE 06High limit manual reset on heater is trippedCE 07Stuck heater relayWhat does STD mean on a hot tub?
Std = Spa operating in Standard Mode. Ecn = Spa operating in Economy Mode.
Why is my hot tub not heating up?If your spa heater won’t heat, remove and clean the filter(s) to rule out a pressure or flow rate problem in your hot tub heater. Low water level, a clogged pump impeller, closed valves, clogged pipes, or blocked spa drain covers can also cause flow issues.
Article first time published onHow long does a hot tub take to heat up?
If your hot tub is located inside, and the air temp is around 76 degrees, it will take about 4 hours to heat up your spa to 100 degrees. The lower the outside temps the longer you will have to wait before your spa is ready. Therefore, by leaving the cover on while it’s heating up you can help it warm up faster.
What does SL mean on a Balboa hot tub?
Balboa topside displaying SL or SLP. If the “SLP” or “SL” Message is Alternating with the Water Temperature on the Topside Display, the Spa is Operating in the “Sleep Heating Mode“. This is NOT an error message. Note that a Sleep Heating Mode will drop the water temperature 20 degrees below the set temperature.
How do I unlock Balboa hot tub?
Spas using Balboa control systems To unlock the panel, while holding down the “Temperature” button (or the “Up” button if you do not have the “Temperature” button), gently press and release the “Light” button twice.
How do I reset my Balboa hot tub?
Remove the spa cover and allow water to cool. At 107¡F (approximately 41.7¡C), the spa should automatically reset. If spa does not reset, shut off the power to the spa. Standby Mode has been activated by pressing a button combination on the user panel.
How do you change mode on Beachcomber?
More. On a 300/500 series hot tub hit the temperature button and then the light button. On a 700 series hot tub hit the temperature button and then the mode button.
What is beachcomber LEEP?
LEEP™ stands for Leaders in Energy Efficient Portables and uses advanced energy efficient technology that lowers energy usage and your cost of operation.
What does Fl mean on Beachcomber hot tub?
Re: Beachcomber FL issue A flashing FL indicates a dirty or clogged filter a solid FL indicates a bad pressure switch.
How do I reset my spa?
- Locate the spa’s high-limit reset. This is a red button found on many spa packs. …
- Press the high-limit reset button. …
- Turn on your spa and observe its operation. …
- Flip the breaker panel switch on or press the reset button on the GFCI outlet to restore power.
Why does my hot tub pump run all the time?
If your spa’s heating element is burnt out, the pump may run all the time. Try turning the thermostat to OFF or LOW to see if the pump turns off. There’s a possibility if it doesn’t stop running that the timer is faulty or something is wrong with the circuit board.
How long does it take to heat a Beachcomber hot tub?
Heating a hot tub to a safe and comfortable temperature of 100 to 102 degrees Fahrenheit usually takes about four hours; it may range from three to eight hours. Generally, water heats up at 5 to 10 degrees Fahrenheit per hour.
How long do Beachcomber Hot Tubs last?
The lower quality hot tubs only last up to 5 years before needing to be replaced. If you purchase a Beachcomber, your hot tub is built to last as long as you need it to! Around the country, there are Beachcomber hot tubs that are over 15 years old and still running like new!
How do I get my Beachcomber out of sleep mode?
Press any button to exit standby mode. Note: If hot tub is in a heat cycle when standby is selected the 2 speed pump or Hush Pump will run for approximately 15 seconds. On all systems, the 2 speed filter pump or Hush Pump and ozone generator will run during filtration.
What temperature should you keep your hot tub when not in use?
While it may sound like common sense to turn your hot tub down every time it is not in use, it’s actually better to maintain a constant soaking temperature, which is typically around 100° Fahrenheit for many people.
What does F2 on a hot tub mean?
The F2 error code is usually from a balboa power pack system and normally is referring to a flow issue in your hot tub. … A dirty filter can often be the culprit here so make sure to either replace or give your hot tub filter a good cleaning. Look at your intakes and out takes and make sure they are clear of debris.
What is Dr code on hot tub?
Newer hot tubs have a digital display for error codes that can assist with troubleshooting. A message such as “dr” or “dry” or “heater dry” is a warning that there’s no water in the heater tube, says Niagara Hot Tubs. … If the water is low, add water to the proper level and try restarting the pump and heater.
Why is my hot tub water cold?
My Water Gets Hot, Cold, Hot Again Start by cleaning your filter, checking for circulation blockages, and topping off your water if necessary. Check whether your pump turns on. Your pump has to be running in order for the spa to heat up. If the pump isn’t working, you may need to replace it.
Does hot tub heat up faster with jets on?
A hot tub heats up faster if the jets are turned on. This is because the water circulates with the jets on, which evenly disperses heat and prevents cold water from being trapped in the hot tub pipes.
How can I heat my hot tub faster?
- Leave the cover on. …
- Turn the jets on. …
- Use a thermal spa blanket. …
- Put a pop-up canopy tent around the tub. …
- Wait for a warm day. …
- Fill up with warm water. …
- Use a portable immersion heater.
What is a good temperature for a hot tub in the summer?
Setting Hot Tub Water Temperature in the Summer As a rule of thumb, many users keep their hot tub set at temperatures ranging between 97-99 degrees.
Should I leave my hot tub on all the time?
One question we sometimes get asked is should I leave my hot tub on all the time? The answer is yes! Hot tubs are designed to be left on permanently and this is how they work best. Of course, they’ll need to be drained regularly but for the most part, they are left on 24/7.
What does EC mean on a Balboa hot tub?
Ecn or Ec is Alternating with Temp: The Spa is Operating in the “Economy” (Ecn or Ec) Heating Mode. The Water Temperature is Sampled Only during Programmed Filter Cycles. The Heater will Only operate and Heat up to Set Temperature during the Filter Cycles.
