How do I put staples in my Bostitch stapler

Place a sleeve of heavy duty staples into the carrying tray, prongs facing downward. On most Bostitch models, a visual aid will be printed on or near the tray to help with loading. Replace the follow block in its cradle and depress the top of it until the spring begins to compress.

How do you load staples into a Bostitch P3 stapler?

Question: How do I load staples into a Bostitch P3 stapler? Answer: Pull the lever on back part of handle to open magazine, then load staples into opening on top of stapler.

How do you load a Bostitch H2B stapler?

Reloading Bostitch H2B Staples Open the front of the stapler and empty unused Bostitch H2B staples. This will help reduce jams. Insert a full stick of Bostitch H2B staples into the tacker. Shut clip and resume using the Bostitch H2B staples tacker.

How do you load a Bostitch stapler 1500?

Flip. Flip the stapler upside down and open the base away from the body.
Pull. Pull the magazine pusher back to expose the staple channel.
Drop. Drop the staples into the magazine channel with the points facing up.
Push.

How do you load a Bostitch stapler T5?

Loading from the Front Bostitch staplers, such as the Bostitch T5, load from the front of the magazine. The magazine cover is located right next to the aperture through which the staples exit when you shoot them. Lift the cover to unhook it and tilt it open.

How do you open the top of a stapler?

Hold the top of the stapler magazine with two fingers and slowly, while maintaining firm pressure, start pulling the lid apart from the part of the magazine that holds the staple. Be careful not to do this too quickly, or the lid might again fly open, spraying the staples all over your office or desk.

Which way do you put staples in a stapler?

Insert the staples upside down into the slide. They should go in with the flat side of the staple being loaded first, and the sharp edges of the staple sticking up. Make sure that the staples you are using are the right size.

What size Staples does a Bostitch electric stapler use?

Attribute nameAttribute valueStaple Pack SizeEachStaple Size1/4″Staple TypePaperStapler CapacityFull-Strip Capacity

What kind of Staples does a Bostitch electric stapler use?

Bostitch B8E electric stapler for paper applications such as mailing and shipping. Staples up to 45 sheets. 2 year limited warranty. Uses STCR2115 staples, 1/4″ and 3/8″.

What staples fit Bostitch H2B?

BOSTITCH 5000 Pack 3/8″ Staples, for H2B Stapler.

Article first time published on

How do you unjam a Bostitch hammer stapler?

In the case of a desk stapler, or manual stapler, remove the pusher or follower block, and remove the remaining staples. Insert a pencil behind where the staples come out under the magazine and press down a few times with the pencil. Tap the hammer against the punch and the jam should clear.

Are 7 32 and 1/4 crown staples the same?

there is no differance between a 7/32 inch bostitch narrow crown stapler and the multitude of 1/4 inch narrow crown staplers currently available in reguards to size.

How do you use the narrow crown stapler?

Remove the Battery or Air Supply and Load the Staples. …
Secure the Magazine and Staples. …
Reconnect the Battery or Air Hose. …
Select the Firing Mode. …
Aim and Fire the Staple. …
Check Fastener Depth/Penetration and Adjust if Needed.

How do you change a Bostitch stapler?

Open it up as you would a standard stapler, pulling the base away from the top handle. Step 2: Slide the magazine out by pulling back the black tab shown below. Step 3: Now is the moment you’ve been waiting for! Drop your stick of staplers into the magazine with the pointed teeth facing up and the flat side down.